Containerised PSA oxygen plant with air compressor, dryer, adsorber towers and oxygen buffer tank

Containerised and Skid-Mounted PSA Oxygen Plants: Sizes, Site Prep and Lead Times

Introduction

India learned the value of a plant-in-a-box in 2021. About 1,225 PSA oxygen plants were installed through the PM CARES fund during and after the second COVID-19 wave (1), and by October 2021 every district in the country had a commissioned PSA oxygen plant (2). DRDO alone installed 931 of them at 869 sites (3). Most were standard, factory-built units that could be shipped, set on a plinth and connected.

The same idea now serves hospitals, mines, fish farms, construction sites and field hospitals. This guide explains what goes into a containerised or skid-mounted PSA oxygen generator, which sizes fit which enclosure, how to prepare the site, and what drives lead time.

Container, Skid or Plant Room?

Feature Skid-mounted Containerised Plant room (built-in)
What it is Generator, compressor, dryer and tanks on one or more steel frames The same equipment inside an ISO shipping container, ventilated and lit Equipment installed in a building on site
Best for Indoor installation in an existing room or shed Sites without a building; temporary, remote or relocatable use Large or permanent plants
Weather protection From the building From the container From the building
Site work Floor, power, ventilation Plinth, power, drainage Civil work, power, ventilation
Relocation Possible Easy (lift and truck) Not practical
Factory testing Full skid can be tested Whole container can be tested Parts tested; system tested on site

Table 1: Skid-mounted, containerised and built-in PSA oxygen plants

Plant Sizes and What Fits Where

PSA oxygen plants are sized in Nm³/h; hospitals usually speak in litres per minute (LPM). 1 Nm³/h is about 16.7 LPM. The air compressor is the largest and heaviest component and sets most of the power, cooling and space needs.

Oxygen output (Nm³/h) Output (LPM) Typical enclosure
5.6 93 Skid
12.5 208 Skid or 20 ft
22 367 Skid or 20 ft
30 500 20 ft
40 667 20 ft high-cube or 40 ft
50 833 20 ft high-cube or 40 ft
65 1,083 40 ft
90 1,500 40 ft or plant room
110 1,833 40 ft or plant room
150 2,500 Plant room or two containers
200 3,333 Plant room or two containers

Table 2: PSA oxygen plant sizes, (sizing tables behind Absstem’s Free Proprietary ROI and Savings Calculator; enclosure is indicative)

The 1,000 LPM size is the one most Indian hospitals know. DRDO’s PM CARES plant was rated at 1,000 LPM, enough for 190 patients at 5 LPM and to charge 195 cylinders a day (4), and CSIR-IIP partners produced a further 120 plants of 500 LPM (5). For a hospital’s own sizing, see our guide to oxygen generators and hospital efficiency (6).

Plants with cylinder filling also need a booster compressor and a filling manifold. Allow extra length in the container, or a separate filling room.

Site Preparation Checklist

A containerised plant saves building work, but not site work. Most delays come from the items below, not from the plant. Our tips for setting up a medical oxygen plant in India cover the hospital side in more detail (7).

1. Location

  • At least 10 m from fire ignition sources and from pollution sources such as generator exhausts, kitchens and incinerators (8).
  • Air intake on the clean, shaded side, away from dust and vehicle exhaust.
  • Truck and crane access for delivery, and space around the container to open doors and change parts.

2. Foundation

  • A level reinforced-concrete plinth or pedestals sized for the loaded container.
  • Anchor points or twist-lock castings as the supplier specifies.
  • Drainage so rainwater does not pool around the container.

3. Power

  • A supply sized for the compressor, dryer and controls. As a first estimate, allow kVA of about 1.25 times the compressor kW and confirm with the supplier.
  • A diesel generator set or second feeder for critical supply (hospitals, hatcheries).
  • Earthing, a lockable isolator and cable routes planned before the container arrives.

4. Cooling and ventilation

  • Air-cooled compressors reject most of their input power as heat. The container needs exhaust fans or ducting sized for that heat, plus intake louvres with filters.
  • In hot regions, check the compressor’s maximum ambient rating against summer peaks.

5. Condensate and drains

  • Compressor and dryer condensate contains moisture & oil. Route it to proper drain.

6. Oxygen connection

  • Pipeline to the hospital manifold or medical gas pipeline system, or to the process line.
  • Isolation valves, pressure gauge, purity sampling point and, for hospitals, a reserve cylinder bank.
  • If filling cylinders for sale or supply, the PESO licence and approvals take time; start them early (9).

What Drives Lead Time

Stage What it depends on
Specification and drawings Flow, purity, pressure, cylinder filling, site data
Long-lead items Air compressor, dryer, molecular sieve, pressure vessels
Fabrication and assembly Standard size or custom layout
Factory test Purity and flow at rated capacity before dispatch
Transport Distance, road access, export packing for overseas sites
Site work (in parallel) Plinth, power, drainage, pipeline, approvals

Table 3: Lead-time drivers for a containerised PSA oxygen plant

Standard sizes move fastest, because the design, drawings and long-lead parts are already known. In 2021, DRDO planned to install 500 standard medical oxygen plants within three months, with production partners targeting 125 plants a month (5). The lesson for buyers: pick a standard size where you can, and start site work and approvals on the day the order is placed.

Internal Resources – Next Steps

Consult Us

For PSA oxygen and nitrogen generators sized to your plant, contact us:

References

  1. IndiaSpend. Why India Must Keep Covid-Era Oxygen Plants Running.
  2. Prime Minister’s Office, Government of India. (2021). PM to Dedicate to the Nation PSA Oxygen Plants Established Under PM CARES.
  3. Daily Excelsior. (2021). DRDO Installed 931 Oxygen PSA Plants: Govt.
  4. Aviation & Defence Universe. (2021). DRDO to Set Up 500 Medical Oxygen Plants Within Three Months Under PM CARES Fund.
  5. Press Information Bureau, Ministry of Defence. (2021). DRDO to Set Up 500 Medical Oxygen Plants Within Three Months Under PM CARES Fund.
  6. Absstem Technologies. (2024). Oxygen Generators and Hospital Efficiency.
  7. Absstem Technologies. (2024). How to Set Up a Medical Oxygen Plant in India: 7 Tips.
  8. The Global Fund and Build Health International. (2024). PSA Oxygen Plant Commissioning Guidelines.
  9. Absstem Technologies. (2026). PESO Licence for Oxygen Cylinder Filling Station in India.
  10. Absstem Technologies. (2026). Industrial Oxygen Plant Cost in India (2026): Full Guide.

Frequently Asked Questions

What size PSA oxygen plant fits in a 20 ft container?

Up to about 500 LPM (30 Nm³/h) fits a standard 20 ft container comfortably; up to about 830 LPM (50 Nm³/h) may fit a 20 ft high-cube depending on layout. Larger plants need a 40 ft container or a plant room.

How much power does a 1,000 LPM oxygen plant need?

Our sizing tables put a 1,083 LPM (65 Nm³/h) plant on a 75 kW air compressor, plus the dryer and controls.

Can a containerised oxygen plant be moved later?

Yes. That is one of its main advantages. Disconnect, lift and truck it to the next site.

Do I need PESO approval for a PSA oxygen plant?

For filling and supplying cylinders, yes. Check the licensing route before ordering.

How long does commissioning take?

For a containerised plant on a ready site, usually days. Site readiness, not the plant, is the usual cause of delay.

ROI Calculator
×

Scroll to Top